View TEA6845H_285419.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

INTEGRATED CIRCUITS
DATA SHEET
TEA6845H New In Car Entertainment (NICE) car radio
Product specification Supersedes data of 2001 Apr 12 2003 Feb 04
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
CONTENTS 1 2 3 4 5 6 7 7.1 7.1.1 7.1.2 7.1.3 7.2 7.2.1 7.2.2 7.2.3 7.2.4 7.2.5 7.3 7.3.1 7.3.2 7.3.3 7.3.4 7.3.5 7.3.6 7.4 8 9 10 11 12 12.1 12.1.1 12.1.2 12.1.3 12.1.4 12.2 12.2.1 12.2.2 12.2.3 12.2.4 12.2.5 12.2.6 12.2.7 12.2.8 13 FEATURES GENERAL DESCRIPTION QUICK REFERENCE DATA ORDERING INFORMATION BLOCK DIAGRAM PINNING FUNCTIONAL DESCRIPTION Oscillators VCO Crystal oscillator PLL FM signal channel DAA FM I/Q mixer FM keyed AGC FM IF amplifiers FM demodulator AM signal channel AM tuner including mixer 1 and mixer 2 AM RF AGC and IF2 AGC AM detector AM AF or IF2 switch AM noise detector and blanker FM and AM level detector Test mode LIMITING VALUES THERMAL CHARACTERISTICS DC CHARACTERISTICS AC CHARACTERISTICS I2C-BUS PROTOCOL I2C-bus specification Test mode Data transfer I2C-bus pull-up resistors Frequency setting I2C-bus protocol Data transfer mode and IC address Write mode: data byte 1 Write mode: data byte 2 Write mode: data byte 3 Write mode: data byte 4 Write mode: data byte 5 Write mode: data byte 6 Read mode: data byte 1 TEST AND APPLICATION INFORMATION 14 15 15.1 15.2 15.3 15.4 15.5 16 17 18 19 PACKAGE OUTLINE SOLDERING
TEA6845H
Introduction to soldering surface mount packages Reflow soldering Wave soldering Manual soldering Suitability of surface mount IC packages for wave and reflow soldering methods DATA SHEET STATUS DEFINITIONS DISCLAIMERS PURCHASE OF PHILIPS I2C COMPONENTS
2003 Feb 04
2
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
1 FEATURES
TEA6845H
* FM mixer for conversion of FM RF from 65 to 108 MHz to IF of 10.7 MHz; the mixer provides inherent image rejection * FM RF mixer can be set to receive weather band radio up to 162.55 MHz; weather band radio flag output * AM mixer 1 for conversion of AM RF to AM IF1 of 10.7 MHz * LC tuner oscillator providing mixer frequencies for FM mixer and AM mixer 1 * AM mixer 2 for conversion of AM IF1 to AM IF2 of 450 kHz * Crystal oscillator providing mixer frequencies for AM mixer 2 and reference for synthesizer PLL, IF count, timing for Radio Data System (RDS) update and reference frequency for car audio signal processor ICs * Fast synthesizer PLL tuning system with local control for inaudible RDS updating * Timing function for RDS update algorithm and control signal output for car audio signal processor ICs (TEA688x, SAA77xx or TEF689x) * Digital auto alignment circuit for conversion of LC oscillator tuning voltage to controlled alignment voltage of FM antenna tank circuit * AGC PIN diode drive circuit for FM RF AGC; AGC detection at FM mixer input; the AGC PIN diode drive can be activated by the I2C-bus as a local or distance function; AGC threshold is a programmable and keyed function switchable via the I2C-bus * FM IF linear amplifiers with high dynamic input range * FM quadrature demodulator with automatic centre frequency adjustment and Total Harmonic Distortion (THD) compensation 3 ORDERING INFORMATION TYPE NUMBER TEA6845H PACKAGE NAME QFP64 DESCRIPTION plastic quad flat package; 64 leads (lead length 1.95 mm); body 14 x 20 x 2.8 mm VERSION SOT319-2 * Level detector for AM and FM with temperature compensated output voltage; starting point and slope of level output is programmable via the I2C-bus * AM RF PIN diode drive circuit; AGC threshold detection at AM mixer 1 and IF2 AGC input; threshold is programmable via the I2C-bus; AM IF2 AGC and demodulator * AM AF output switchable to provide AM IF2 for AM stereo decoder * AM noise blanker with blanking at AM IF2 * Several test modes available for fast IC and system tests. 2 GENERAL DESCRIPTION
The TEA6845H is a single IC with car radio tuner for AM and FM intended for microcontroller tuning with the I2C-bus. It provides the following functions: * AM double conversion receiver for LW, MW and SW (31 m, 41 m and 49 m bands) with IF1 = 10.7 MHz and IF2 = 450 kHz * FM single conversion receiver with integrated image rejection for IF = 10.7 MHz capable of selecting US FM, US weather, Europe FM, East Europe FM and Japan FM bands.
2003 Feb 04
3
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
4 QUICK REFERENCE DATA SYMBOL VDDA(n) IDDA(tot) VDDA2 IDDA2 VDDD IDDD fAM(ant) PARAMETER analog supply voltage 1, 3, 4, 5 and 6 total analog supply current 1, 3, 4, 5 and 6 analog supply voltage 2 analog supply current 2 digital supply voltage digital supply current AM input frequency FM mode AM mode LW MW SW fFM(ant) fFM(WB)(ant) Tamb (S+N)/N THD FM input frequency FM weather band input frequency ambient temperature FM mode AM mode FM mode AM mode CONDITIONS 8 45 39 4.75 6.5 4.7 4.75 18 18 0.144 0.522 5.85 65 162.4 -40 m = 0.3 m = 0.8 m = 0.9 FM overall system parameters (3 x SFE10.7MS3) (S+N)/N THD signal plus noise-to-noise ratio total harmonic distortion f = 22.5 kHz; de-emphasis = 50 s f = 75 kHz - - 65 0.6 - - - MIN. TYP. 8.5 56 49 5 8.1 5.9 5 23 23 - - - - - - 58 0.3 0.5
TEA6845H
MAX. 9 67 59 5.25 9.8 7.1 5.25 28 28 0.288 1.710 9.99 108 162.55 +85 - - - - 1
UNIT V mA mA V mA mA V mA mA MHz MHz MHz MHz MHz C dB % %
AM overall system parameters (1 x SFE10.7MS3; 1 x SFR450H) signal plus noise-to-noise ratio total harmonic distortion
dB %
2003 Feb 04
4
This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in _white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ... 2003 Feb 04
DAAIN 33 Vtune CPOUT 34 35 VDDA4 FREF VDDD 36 37 38 39 DAATD DAAOUT 32 31 ANTENNA DAA TUNING SYSTEM AM 10.25 MHz I2C-bus T1FMAGC T2FMAGC IFMAGC 30 29 28 FM AGC WX FM IF AM IF2 IF COUNT I2C-BUS 2 ms/20 ms 52 SDA 53 SCL 54 55 AM IF AGC LEVEL DAA DEMODULATOR 56 QDET2 IF2GND QDET1 VCO FMMIXIN2 RFGND FMMIXIN1 27 26 25 FM I/Q MIXER
5
Philips Semiconductors
New In Car Entertainment (NICE) car radio
BLOCK DIAGRAM
DGND
OSCFDB
VDDA3
AFHOLD AFSAMPLE
AMAFIF2 RDSMPX FMMPX 47 48 49 VDDA2 VDDA1 50 51
VCOGND OSCTNK 40 41 42 43
TRDSMUTE 45 46
44
SEQUENTIAL CIRCUIT FOR RDS UPDATING
AM DETECTOR
MUTE
POWER SUPPLY
TEA6845H
x
N1
/2
90 57
handbook, full pagewidth
5
Vref(FMMIX) 24 90 AM-NOISE DETECTOR PEAK/ AVERAGE BLANK PULSE AM LEVEL
CAFC
58 Vlevel
59 IAMAGC T2AMAGC T1AMAGC 23 22 21 AM RF AGC N2
/5/10
AM MIXER 2
x
FM LIMITER/ LEVEL
XTAL1 XTALGND XTAL2 IREF
CRYSTAL OSCILLATOR
60 61 62
AMMIX1IN1
20
AM MIXER 1
x
IFAMP 1
IFAMP 2 63 64 AMMIX2OUT1 AMMIX2OUT2
19 AMMIX1IN2
18
17
16
15 14 IFAMP1DEC
13
12 IFAMP1OUT
11
10 Coffset
9
8 IF1GND
7
6
5
4
3 FMLIMIN
2
1
MGU350
Product specification
TEA6845H
MIX1OUT2
IFAMP1IN
CAGC
VDDA5
MIX1OUT1
VDDA6
IFAMP2DEC
IFAMP2IN
AMIF2IN AMNBHOLD
AMIF2DEC
FMLIMDEC
IFAMP2OUT
Fig.1 Block diagram.
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
6 PINNING SYMBOL CAGC FMLIMDEC FMLIMIN AMIF2DEC IFAMP2OUT AMNBHOLD AMIF2IN IF1GND IFAMP2IN Coffset IFAMP2DEC IFAMP1OUT IFAMP1IN VDDA6 IFAMP1DEC MIX1OUT1 MIX1OUT2 VDDA5 AMMIX1IN2 AMMIX1IN1 T1AMAGC T2AMAGC IAMAGC Vref(FMMIX) FMMIXIN1 RFGND FMMIXIN2 IFMAGC T2FMAGC T1FMAGC DAAOUT DAATD DAAIN Vtune CPOUT VDDA4 FREF VDDD DGND VCOGND 2003 Feb 04 PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 AM IF AGC capacitor FM limiter decoupling FM limiter input (10.7 MHz) decoupling for AM IF2 input IF amplifier 2 output (10.7 MHz) AM noise blanker threshold AM IF2 input (450 kHz) for demodulator AGC and AM level detector AM IF1 ground IF amplifier 2 input (10.7 MHz) DC feedback for offset compensation RDS mute IF amplifier 2 decoupling and AGC capacitor for AM noise blanker IF amplifier 1 output (10.7 MHz) IF amplifier 1 and AM mixer 2 input (10.7 MHz) analog supply voltage 6 (8.5 V) for IF amplifier 1 and 2 AM mixer 2 and FM IF amplifier 1 decoupling FM mixer and AM mixer 1 IF output 1 (10.7 MHz) FM mixer and AM mixer 1 IF output 2 (10.7 MHz) analog supply voltage 5 (8.5 V) for FM mixer and AM mixer 1 AM mixer 1 input 2 AM mixer 1 input 1 1st time constant of AM front-end AGC 2nd time constant of AM front-end AGC PIN diode drive current output of AM front-end AGC reference voltage for FM I/Q mixer FM RF mixer input 1 RF ground FM RF mixer input 2 PIN diode drive current output of FM front-end AGC 2nd time constant of FM front-end AGC 1st time constant of FM front-end AGC output of digital auto alignment circuit for antenna tank circuit DESCRIPTION
TEA6845H
temperature compensation diode for digital auto alignment circuit for antenna tank circuit input of digital auto alignment circuit for antenna tank circuit tuning voltage charge pump output analog supply voltage 4 (8.5 V) for tuning PLL reference frequency output for signal processor IC digital supply voltage (5 V) digital ground VCO ground 6
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
TEA6845H
SYMBOL OSCFDB OSCTNK VDDA3 AFSAMPLE AFHOLD TRDSMUTE AMAFIF2 RDSMPX FMMPX VDDA2 VDDA1 SDA SCL IF2GND QDET1 QDET2 CAFC Vlevel XTAL1 XTALGND XTAL2 IREF AMMIX2OUT1 AMMIX2OUT2
PIN 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 VCO feedback VCO tank circuit
DESCRIPTION
analog supply voltage 3 (8.5 V) for VCO AF sample flag output for car audio signal processor IC AF hold flag output for car audio signal processor IC time constant for RDS update mute AM demodulator AF output or IF2 output for AM stereo (multiplexed by I2C-bus) MPX output for RDS decoder and signal processor (not muted) FM demodulator MPX output analog supply voltage 2 (5 V) for on-chip power supply analog supply voltage 1 (8.5 V) for on-chip power supply I2C-bus data line input and output I2C-bus clock line input AM IF2 ground quadrature demodulator tank 1 quadrature demodulator tank 2 FM demodulator AFC capacitor level voltage output for AM and FM crystal oscillator 1 crystal oscillator ground crystal oscillator 2 reference current for power supply AM mixer 2 output 1 (450 kHz) AM mixer 2 output 2 (450 kHz)
2003 Feb 04
7
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
TEA6845H
handbook, full pagewidth
63 AMMIX2OUT1
64 AMMIX2OUT2
60 XTALGND
54 IF2GND
56 QDET2
55 QDET1
61 XTAL2
59 XTAL1
57 CAFC
58 Vlevel
62 IREF
52 SDA
53 SCL
CAGC FMLIMDEC FMLIMIN AMIF2DEC IFAMP2OUT AMNBHOLD AMIF2IN IF1GND IFAMP2IN
1 2 3 4 5 6 7 8 9
51 VDDA1 50 VDDA2 49 FMMPX 48 RDSMPX 47 AMAFIF2 46 TRDSMUTE 45 AFHOLD 44 AFSAMPLE 43 VDDA3
Coffset 10 IFAMP2DEC 11 IFAMP1OUT 12 IFAMP1IN 13 VDDA6 14 IFAMP1DEC 15 MIX1OUT1 16 MIX1OUT2 17 VDDA5 18 AMMIX1IN2 19
AMMIX1IN1 20 T1AMAGC 21 T2AMAGC 22 IAMAGC 23 Vref(FMMIX) 24
TEA6845H
42 OSCTNK 41 OSCFDB 40 VCOGND 39 DGND 38 VDDD 37 FREF 36 VDDA4 35 CPOUT 34 Vtune 33 DAAIN
FMMIXIN1 25
RFGND 26
FMMIXIN2 27
IFMAGC 28
T2FMAGC 29
T1FMAGC 30
DAAOUT 31
DAATD 32
MHB877
Fig.2 Pin configuration.
2003 Feb 04
8
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
7 7.1 7.1.1 FUNCTIONAL DESCRIPTION Oscillators VCO 7.2.3 FM KEYED AGC
TEA6845H
The L and C tuned VCO provides the local oscillator signal for both FM and AM mixer 1. It has a frequency range of 151.2 to 248.2 MHz. 7.1.2 CRYSTAL OSCILLATOR
FM contains keyed wide-band RF AGC. AGC detection occurs at the FM mixer. The wide-band RF signal switches a narrow band signal (IF) from the FM IF level detector circuitry that controls the FM RF AGC block. It includes an AGC PIN diode drive circuit for the FM RF AGC. The PIN diode drive can be activated via the I2C-bus as a local or distance function. The AGC threshold is programmable and the keyed AGC function is switchable via the I2C-bus. 7.2.4 FM IF AMPLIFIERS
The crystal oscillator provides a 20.5 MHz signal that is used for: * Reference frequency for frequency synthesizer PLL * Local oscillator for AM mixer 2 * Reference frequency for the IF counter * Timing signal for the RDS update algorithm * Reference frequency (75.4 kHz) for the TEA6880H (car audio signal processor - CASP) or TEF6890H (car radio integrated signal processor). 7.1.3 PLL
The two FM IF amplifiers provide 10 dB and 4 dB amplification with high linearity and dynamic range. 7.2.5 FM DEMODULATOR
The FM quadrature demodulator includes automatic centre frequency adjustment and THD compensation. 7.3 7.3.1 AM signal channel AM TUNER INCLUDING MIXER 1 AND MIXER 2
Fast synthesizer PLL tuning system with local control for inaudible RDS updating. 7.2 7.2.1 FM signal channel DAA
The AM tuner is realized in a double conversion technique and is capable of selecting LW, MW and SW bands. AM mixer 1 converts AM RF to IF1 of 10.7 MHz, while AM mixer 2 converts IF1 of 10.7 MHz to IF2 of 450 kHz: * LW = 144 to 288 kHz * MW = 530 to 1710 kHz (US AM band) * SW = 5.85 to 9.99 MHz (including the 31 m, 41 m and 49 m bands). 7.3.2 AM RF AGC AND IF2 AGC
FM RF Digital Auto Alignment (DAA) circuitry for the conversion of the VCO tuning voltage to a controlled alignment voltage for the FM antenna tank circuit. 7.2.2 FM I/Q MIXER
FM quadrature mixer converts FM RF (65 to 162.55 MHz) to IF of 10.7 MHz. The FM mixer provides inherent image rejection and high RF sensitivity. It is capable of tuning the US FM, US weather, Europe FM, Japan FM and East Europe FM bands: * US FM = 87.9 to 107.9 MHz * US weather FM = 162.4 to 162.55 MHz * Europe FM = 87.5 to 108 MHz * Japan FM = 76.0 to 91 MHz * East Europe FM = 65.8 to 74 MHz.
The AM RF includes a PIN diode drive circuit. The threshold detection points for AM AGC are performed at AM mixer 1 and AM IF2. AGC thresholds are programmable via the I2C-bus. 7.3.3 AM DETECTOR
The AM detector provides AM level information and AM AF or AM IF2. 7.3.4 AM AF OR IF2 SWITCH
The AM output provides either a detected AM AF or the corresponding AM IF2 signal. The IF2 signal can be used for AM stereo decoder processing.
2003 Feb 04
9
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
7.3.5 AM NOISE DETECTOR AND BLANKER
TEA6845H
If the test mode is enabled by pin FREF: * The settling time of the AM IF2 AGC is reduced to less than 100 ms in the nominal application * The digital-to-analog converters for the antenna DAA and the level DAA can be clocked directly by the SCL line of the I2C-bus * The output at pin FREF can be selected by the I2C-bus: TEA6880H or TEF6890H reference frequency, PLL reference frequency or PLL programmable divider output frequency * The RDS update control circuit can be clocked directly via pin DAATD * Pin T1AMAGC can be used to enable the load PLL circuit of the RDS update control circuit * Charge pumps can be set into 3-state mode.
The detection point for the AM noise blanker is the output stage of AM mixer 1, while blanking is realized at the output of the mixer 2. Trigger sensitivity can be modified by changing the resistor value at pin AMNBHOLD. 7.3.6 FM AND AM LEVEL DETECTOR
FM and AM level detectors provide the temperature compensated output voltage. The starting points and slopes of the level detector outputs are programmable via the I2C-bus. 7.4 Test mode
The test mode of the IC is activated by: * Sending the test byte (byte 5) to the IC * Connecting pin FREF through a 100 k resistor to VDDA1 * Applying 50 A to pin FREF.
8 LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 60134). SYMBOL VDDA1 VDDA2 VDDA3 VDDA4 VDDA5 VDDA6 VDDD PARAMETER analog supply voltage 1 for on-chip power supply analog supply voltage 2 for on-chip power supply analog supply voltage 3 for VCO analog supply voltage 4 for tuning PLL analog supply voltage 5 for FM and AM RF analog supply voltage 6 for IF amplifier 1 and 2 digital supply voltage note 1 CONDITIONS MIN. -0.3 -0.3 -0.3 -0.3 -0.3 -0.3 -0.3 -0.3 -55 -40 note 2 note 3 Notes 1. To avoid damage and wrong operation it is necessary to keep all 8.5 V supply voltages at a higher level than any 5 V supply voltage. This is also necessary during power-on and power-down sequences. Precautions have to be provided in such a way that interference cannot pull the 8.5 V supply down below the 5 V supply. 2. Machine model (R = 0 , C = 200 pF). 3. Human body model (R = 1.5 k, C = 100 pF). -200 -2000 MAX. +10 +6.5 +10 +10 +10 +10 +6.5 - +150 +85 +200 +2000 V V V V V V V V C C V V UNIT
VDD8.5-DD5 difference between any 8.5 V supply voltage and any 5 V supply voltage Tstg Tamb Ves storage temperature ambient temperature electrostatic handling voltage
2003 Feb 04
10
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
9 THERMAL CHARACTERISTICS SYMBOL Rth(j-a) PARAMETER thermal resistance from junction to ambient CONDITIONS in free air
TEA6845H
VALUE 48
UNIT K/W
10 DC CHARACTERISTICS VDDA1 = VDDA3 = VDDA4 = VDDA5 = VDDA6 = 8.5 V; VDDA2 = 5 V; VDDD = 5 V; Tamb = 25 C; unless otherwise specified. SYMBOL Supply voltage VDDA(n) VDDA2 VDDD IDDD IDDA1 IDDA2 IDDA3 IDDA4 IDDA5 IDDA6 IMIX1OUT1 IMIX1OUT2 IDDD IDDA1 IDDA2 IDDA3 IDDA4 IDDA5 IMIX1OUT1 IMIX1OUT2 analog supply voltage 1, 3, 4, 5 and 6 analog supply voltage 2 digital supply voltage 8 4.75 4.75 8.5 5 5 9 5.25 5.25 V V V PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
Supply current in FM mode digital supply current analog supply current 1 for on-chip power supply analog supply current 2 for on-chip power supply analog supply current 3 for VCO analog supply current 4 for tuning PLL analog supply current 5 for FM RF analog supply current 6 for FM IF amplifier 1 and 2 bias current of FM mixer output 1 bias current of FM mixer output 2 18 - 6.5 - test mode; bit TMS3 = 1 - - 10 4.8 4.8 23 15 8.1 6.5 2.9 5 12 6 6 28 - 9.8 - - - 14 7.2 7.2 mA mA mA mA mA mA mA mA mA
Supply current in AM mode digital supply current analog supply current 1 for on-chip power supply analog supply current 2 for on-chip power supply analog supply current 3 for VCO analog supply current 4 for tuning PLL analog supply current 5 for RF bias current of AM mixer 1 output 1 bias current of AM mixer 1 output 2 18 - 4.7 - test mode; bit TMS3 = 1 - - 4.8 4.8 3.6 3.6 23 17.5 5.9 6.5 1.6 1.8 6 6 4.5 4.5 28 - 7.1 - - - 7.2 7.2 5.4 5.4 mA mA mA mA mA mA mA mA mA mA
IAMMIX2OUT1 bias current of AM mixer 2 output 1 IAMMIX2OUT2 bias current of AM mixer 2 output 2 On-chip power supply reference current generator: pin IREF Vo(ref) Ro Io(max) output reference voltage output resistance maximum output current
4 8 -100
4.25 11 -
4.5 13 +100
V k nA
2003 Feb 04
11
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
TEA6845H
11 AC CHARACTERISTICS VDDA1 = VDDA3 = VDDA4 = VDDA5 = VDDA6 = 8.5 V; VDDA2 = 5 V; VDDD = 5 V; Tamb = 25 C; see Figs 9 and 10; unless otherwise specified. SYMBOL PARAMETER CONDITIONS MIN. - 101 TYP. MAX. UNIT
Voltage controlled oscillator fosc C/N RR oscillator frequency carrier-to-noise ratio ripple rejection fosc = 200 MHz; f = 10 kHz fripple = 100 Hz; VDDA3(ripple) = 100 mV (RMS) fosc = 250 MHz fosc = 200 MHz FEEDBACK INPUT: PIN OSCFDB Vi(bias) VO Vo(rms) input bias voltage 2.2 2.8 3.4 V - - 97 99 - - dB dB 151.2 - 248.2 - MHz dBc ----------Hz
TANK CIRCUIT OUTPUT: PIN OSCTNK DC output voltage AC output voltage (RMS value) fosc = 200 MHz 5 - 6.1 1.5 7.2 - V V
Crystal oscillator fxtal Rxtal Cxtal C/N crystal frequency crystal motional resistance crystal shunt capacitance carrier-to-noise ratio fxtal = 20.5 MHz (10.25 MHz); f = 10 kHz start of operating 20.4996 - - - 20.5 - - 112 20.5004 500 18 - MHz pF dBc ----------Hz
CIRCUIT INPUTS: PINS XTAL1, XTAL2 AND XTALGND Vxtal(rms) VXTAL1, VXTAL2 Ri Ci IXTALGND crystal voltage (RMS value) DC bias voltage real part of input impedance input capacitance crystal oscillator circuit current VXTAL1 - VXTAL2 = 1 mV; note 1 note 1 start-up at VXTAL1 = VXTAL2 = 2.1 V operating at VXTAL1 - VXTAL2 = 400 mV Oscillator divider N1 N1 oscillator divider ratio FM mode standard, Europe and local weather band (WX) - - 2 1 - - note 1 - 1.7 -500 8 - - 350 2.1 - 10 9 1.5 - 2.5 - 12 - - mV V pF mA mA
2003 Feb 04
12
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
TEA6845H
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Oscillator divider N2 N2 oscillator divider ratio AM mode LW and MW SW Synthesizer PROGRAMMABLE DIVIDER Nprog Nstep programmable divider ratio programmable divider step size 512 - - 1 32767 - - - 10 5 - -
REFERENCE FREQUENCY DIVIDER Nref crystal oscillator divider ratio fxtal = 20.5 MHz fref = 100 kHz fref = 50 kHz fref = 25 kHz fref = 20 kHz fref = 10 kHz CHARGE PUMP: PIN CPOUT Isink(cp1)l Isource(cp1)l Isink(cp1)h low charge pump 1 peak sink current low charge pump 1 peak source current high charge pump 1 peak sink current high charge pump 1 peak source current charge pump 2 peak sink current charge pump 2 peak source current FM weather band mode; 0.4 V < VCPOUT < 7.6 V FM weather band mode; 0.4 V < VCPOUT < 7.6 V AM stereo mode; N2 = 10 (LW and MW); 0.4 V < VCPOUT < 7.6 V AM stereo mode; N2 = 10 (LW and MW); 0.4 V < VCPOUT < 7.6 V FM standard mode; 0.3 V < VCPOUT < 7.1 V FM standard mode; 0.3 V < VCPOUT < 7.1 V 0 < VCPOUT < 8.5 V 200 -400 0.7 300 -300 1 400 -200 1.3 A A mA - - - - - 205 410 820 1025 2050 - - - - -
Isource(cp1)h
-1.3
-1
-0.7
mA
Isink(cp2) Isource(cp2)
100 -160 -5
130 -130 -
160 -100 +5
A A nA
IZ(cp1), IZ(cp2) charge pump 1 or 2 current in 3-state CHARGE PUMP: PIN Vtune Isink(cp3) Isource(cp3) IZ(cp3) charge pump 3 peak sink current charge pump 3 peak source current charge pump 3 current in 3-state
FM standard mode; 0.4 V < Vtune < 7.6 V FM standard mode; 0.4 V < Vtune < 7.6 V 0 < Vtune < 8.5 V
2.1 -3.9 -5
3 -3 -
3.9 -2.1 +5
mA mA nA
2003 Feb 04
13
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
TEA6845H
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Antenna Digital Auto Alignment (DAA) DAA INPUT: PIN DAAIN Ibias(cp) charge pump buffer input bias current FM mode; 0.4 V < VDAAIN < 8.0 V AM mode; 0 V < VDAAIN < 8.5 V Vi(cp) charge pump buffer input voltage -10 -10 0 - - - +10 +10 8.5 nA nA V
DAA OUTPUT: PIN DAAOUT; note 2 Vo(AM) Vo(FM) DAA output voltage in AM mode DAA output voltage in FM mode VDAAIN = 4.0 V; VDAATD = 0.7 V minimum value bits DAA[6:0] set to logic 0 value: data byte 3 = 10101011 maximum value; bits DAA[6:0] set to logic 1 VDAAIN = 3.0 V; VDAATD = 0.7 V; bits DAA[6:0] set to logic 1 VDAAIN = 2 V data byte 3 = 11010101 data byte 3 = 10101010 Vo(n) DAA output noise voltage FM mode; VDAAIN = 4 V; data byte 3: bit 6 = 1, bits 5 to 0 = 0; B = 300 Hz to 15 kHz Tamb = -40 to +85 C; data byte 3 = 10101011; VDAATD = 0.7 V FM mode; VDAAOUT < 8.0 V; n = 0 to 127 0.2 V < VDAAOUT < 8.25 V 0.2 V < VDAAOUT < 8.25 V; CL = 270 pF fripple = 100 Hz; VDDA4 = 1 mV VDAAOUT < 8.0 V; FM mode 3 1.8 - 3.3 2 30 3.6 2.2 100 V V V - 1.5 3.8 8 6.2 - 1.65 4 - 6.5 0.5 1.8 4.2 8.5 6.8 V V V V V - - 0.3 V
Vo(T)
DAA output voltage variation with temperature DAA step accuracy DAA output sink current DAA output source current DAA output settling time ripple rejection DAA output load capacitance
-8
-
+8
mV
Vo(step) Io(sink) Io(source) tst RR CL
0.5VLSB 50 - - - -
VLSB - - - 50 -
1.5VLSB - -50 30 - 270
mV A A s dB pF
2003 Feb 04
14
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
TEA6845H
SYMBOL
PARAMETER
CONDITIONS
MIN. -50 -300
TYP. -40 -
MAX. -30 +300
UNIT A 10 ----------K
-6
DAA TEMPERATURE COMPENSATION: PIN DAATD Isource TCsource compensation diode source current temperature coefficient of compensation diode source current 0.2 V < VDAATD < 1.5 V 0.2 V < VDAATD < 1.5 V; Tamb = -40 to +85 C
IF counter (FM IF or AM IF2 counter) NIF Tcount(IF) Rprecount IF counter length for AM and FM IF counter period FM IF counter prescaler ratio data byte 4: bit 7 = 1 data byte 4: bit 7 = 0 data byte 4: bit 3 = 1 data byte 4: bit 3 = 0 - - - - - 8 2 20 10 100 - - - - - bit ms ms
Reference frequency for car sound processor IC; note 3 REFERENCE FREQUENCY DIVIDER Nref fref Vo(p-p) VO Ro RL(min) crystal oscillator divider ratio reference frequency fxtal = 20.5 MHz - - 60 3.2 - 1 272 75.368 - - 170 3.9 50 - kHz
VOLTAGE GENERATOR; PIN FREF AC output voltage (peak-to-peak value) DC output voltage output resistance minimum load resistance 100 3.4 - - mV V k M
AM signal channel AM RF AGC STAGE INPUTS: PINS AMMIX1IN1 AND AMMIX1IN2 Vi(p) RF input voltage for AGC start level (peak value) data byte 5: bit 5 = 0, bit 6 = 0 - data byte 5: bit 5 = 1, bit 6 = 0 - data byte 5: bit 5 = 0, bit 6 = 1 - data byte 5: bit 5 = 1, bit 6 = 1 - AM IF AGC STAGE INPUTS: PINS AMIF2IN AND AMIF2DEC Vi(p) IF2 input voltage (peak value) AGC start level 0.20 0.27 0.35 V 150 275 400 525 - - - - mV mV mV mV
AM RF AGC CURRENT GENERATOR OUTPUT: PIN IAMAGC Isink(max) Ro Co maximum AGC sink current output resistance output capacitance VAMMIX1IN1 > 500 mV (peak value) IIAMAGC = 1 A - 1 - 15 - 5 - - 7 mA M pF
2003 Feb 04
15
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
TEA6845H
SYMBOL
PARAMETER
CONDITIONS -
MIN.
TYP. -3.15 -
MAX.
UNIT
AM RF AGC PEAK DETECTOR: PIN T2AMAGC Iatt attack current AGC peak detector data byte 5: bit 5 = 1, bit 6 = 1; AM mixer 1 input Vi = 1 V; VT2AMAGC-GND = 3 V; VAMIF2IN-AMIF2DEC = 0 V data byte 5: bit 5 = 1, bit 6 = 1; AM mixer 1 input Vi = 0 V; VT2AMAGC-AMMIX1IN2 = 0.25 V; VT2AMAGC-GND = 3 V; VAMIF2IN-AMIF2DEC = 0 V mA
Idec
decay current AGC peak detector
-
2.6
-
A
AM MIXER 1 (IF1 = 10.7 MHZ)
Mixer inputs: pins AMMIX1IN1 and AMMIX1IN2
Ri Ci VI Vi(max) input resistance input capacitance DC input voltage maximum voltage on pin AMMIX1IN1 1 dB compression point of AM mixer 1 output (peak-to-peak) note 4 note 4 50 - 2.3 500 70 5 2.7 - 100 7 3.1 - k pF V mV
Mixer outputs: pins MIX1OUT1 and MIX1OUT2
Ro Co Vo(max)(p-p) Ibias output resistance output capacitance maximum output voltage (peak-to-peak value) mixer bias current AM mode note 5 note 5 100 - 12 4.8 - 5 15 6 - 7 - 7.2 k pF V mA
Mixer
gm(conv) conversion transconductance I MIXOUT1 -------------------------------------------------V FMMIXIN1 - FMMIXIN2 conversion transconductance variation with temperature g m(conv) -------------------------------g m(conv) x T 3rd-order intermodulation 2nd-order intermodulation equivalent input noise voltage 2.0 2.55 3.2 mA -------V
gm(conv)(T)
-
-9 x 10-4 -
K-1
IP3 IP2 Vi(n)(eq)
RL = 2.8 k (AC load between 135 output pins) RL = 2.8 k (AC load between - output pins) band limited noise; - Rgen = 750 ; RL = 2.8 k (AC load between output pins) 16
138 170 5.8
- - -
dBV dBV nV ----------Hz
2003 Feb 04
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
TEA6845H
SYMBOL F
PARAMETER noise figure of AM mixer 1
CONDITIONS - -5 measured with respect to pin RFGND measured with respect to pin RFGND 0
MIN.
TYP. 4.5 - - 6.0
MAX. 7.1
UNIT dB A V V
WEATHER BAND FLAG: PIN T1AMAGC IL(max) Vo(max) Vo(min) maximum load current maximum output voltage for FM mode minimum output voltage for WX mode +5 0.5 6.9
5.1
AM MIXER 2 (IF2 = 450 kHz)
Mixer inputs: pins IFAMP1IN and IFAMP1DEC
Ri Ci VI Vi(max)(p) input resistance input capacitance DC input voltage maximum input voltage (peak value) 1 dB compression point of AM mixer 2 output (peak-to-peak) note 6 note 6 270 - 2.4 1.1 330 5 2.7 - 390 7 3 - pF V V
Mixer outputs: pins AMMIX2OUT1 and AMMIX2OUT2
R0 Co Vo(max)(p-p) Ibias output resistance output capacitance maximum output voltage (peak-to-peak value) mixer bias current note 7 note 7 VDDA = 8.5 V AM mode 100 - 12 3.6 - 5 15 4.5 - 7 - 5.4 k pF V mA
Mixer
gm(conv) conversion transconductance I AMMIX2OUT1 -----------------------------V IFAMP1IN conversion transconductance variation with temperature g m(conv) -------------------------------g m(conv) x T 3rd-order intermodulation 2nd-order intermodulation equivalent input noise voltage noise figure of AM mixer 2 RL = 4 k (AC load between output pins) RL = 4 k (AC load between output pins) 1.3 1.6 1.9 mA -------V
gm(conv)(T)
-
-9 x 10-4 -
K-1
IP3 IP2 Vi(n)(eq) F
134 -
137 170 15 16
- - 22 19.5
dBV dBV nV ----------Hz dB
Rgen = 330 ; RL = 4 k - (AC load between output pins) -
2003 Feb 04
17
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
TEA6845H
SYMBOL Vi
PARAMETER input voltage
CONDITIONS for = -10 dB audio attenuation AM soft mute on AM soft mute off - - - 1
MIN.
TYP.
MAX.
UNIT
AM IF2 AGC STAGE: PINS AMIF2IN AND AMIF2DEC; note 8
75 6 14 - 4.3 89 2 -
120 10 30 - 4.7 - 2.2 5
V V V V V dB k pF
VAGC(start) VAGC(stop) VAGC(ctrl) AGC Ri Ci AM DETECTOR Vsens(rms)
AGC start voltage AGC stop voltage AGC control voltage AGC range input resistance input capacitance
input carrier voltage maximum input peak voltage Vi = 1 mV between start and stop of AGC; m = 0.8
4.1 - 1.8 -
sensitivity voltage (RMS value)
m = 0.3; fmod = 400 Hz; BAF = 2.5 kHz; Rgen = 2 k; note 8 (S+N)/N = 26 dB (S+N)/N = 46 dB - - 54 45 600 60 65 900 - V V dB
(S+N)/N THD
maximum signal plus noise-to-noise ratio total harmonic distortion
m = 0.3; fmod = 400 Hz; BAF = 2.5 kHz; Rgen = 2 k BAF = 2.5 kHz; CAGC = 22 F; AM IF2 AGC input Vi = 100 V to 500 mV (RMS) m = 0.8; fmod = 400 Hz m = 0.9; fmod = 400 Hz m = 0.8; fmod = 100 Hz m = 0.9; fmod = 100 Hz
- - - - 30 - - -
0.5 1 1.25 1.75 40 1000 - -
1 2 2.5 3.5 - 1500 1800 180
% % % % dB ms ms ms
RR tsw tsettle
ripple rejection FM to AM switching time AM AGC settling time
VDDA2(ripple) = 100 mV (RMS); fripple = 100 Hz CAGC = 22 F CAGC = 22 F normal operation test mode
Output: pin AMAFIF2
Vo(rms) AM IF2 output voltage (RMS value) AM stereo; m = 0 minimum at Vi = 14 V maximum at Vi = 5.0 mV 1.5 130 3 180 290 4.5 230 340 mV mV mV
AM mono; m = 0.3; 240 fmod = 400 Hz; Vi = 100 V to 500 mV (RMS) Ro output resistance AM stereo AM mono - -
- -
500 500

2003 Feb 04
18
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
TEA6845H
SYMBOL Co Vlevel
PARAMETER output capacitance
CONDITIONS AM mono Vi = 10 V to 1 V Vi < 1 V; standard setting of level DAA and level slope Vi = 1.4 mV; standard setting of level DAA - 0
MIN. 5 -
TYP. 7
MAX.
UNIT pF
AM IF2 LEVEL DETECTOR OUTPUT: PIN Vlevel; see Fig.3 DC output voltage 7 0.9 2.8 50 950 75 - 500 - V V V mV mV -------------20 dB mV -------------20 dB kHz dB 0.1 1.6 0.5 2.2 40 800 60 300 - 40
Vlevel Vlevel(slope) Vstep Blevel Ro RR
step size for adjustment of standard setting of level slope 30 level starting point slope of level voltage standard setting of level slope 650 45 200 - VDDA1(ripple) = 100 mV (RMS); fripple = 100 Hz -
step size for adjustment of Vi =1.4 mV level slope bandwidth of level output voltage output resistance ripple rejection
AM NOISE BLANKER; see Fig.4
Threshold: pin AMNBHOLD
VO tsup ftrigger DC output voltage suppression time trigger sensitivity frequency Vpulse = 200 mV (peak); Vlevel < 1.8 V Vpulse = 200 mV (peak); Vlevel > 2.2 V Vpulse = 20 mV (peak); Vlevel < 1.8 V 4.3 6 - - - 4.6 7.5 1000 - - 5.1 10 - 100 100 V s Hz Hz Hz
Noise detector output: pin TRDSMUTE
Isink(AGC) VAGC AM noise blanker AGC sink current AM noise blanker AGC voltage VTRDSMUTE = 3 V AM mixer 1 input Vi = 0 V 35 1.9 50 2.2 65 2.5 A V
FM signal channel FM RF AGC
Inputs: pins FMMIXIN1 and FMMIXIN2; note 9
Vi(RF)(rms) RF input voltage for start of wide-band AGC (RMS value) data byte 5: bit 5 = 0, bit 6 = 0 - data byte 5: bit 5 = 1, bit 6 = 0 - data byte 5: bit 5 = 0, bit 6 = 1 - data byte 5: bit 5 = 1, bit 6 = 1 - 4 8 12 16 - - - - mV mV mV mV
2003 Feb 04
19
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
TEA6845H
SYMBOL
PARAMETER
CONDITIONS
MIN. -350 15
TYP. -600 25
MAX. -850 35
UNIT A A mA
AGC peak detector output: pin T1FMAGC
Ich Idch Idrive Vth FM RF MIXER charge current discharge current
PIN diode drive output: pin IFMAGC
drive current Vo = 0.5 to 4.0 V data byte 5: bit 7 = 1; standard setting of level DAA 8 11.5 15
Level voltage output: pin Vlevel
threshold voltage for narrow-band AGC 500 950 1400 mV
Reference voltage: pin Vref(FMMIX)
Vref reference voltage FM mode AM mode 6.5 2.7 7.1 3.1 7.9 3.4 - V V
Inputs: pins FMMIXIN1 and FMMIXIN2; note 9
Vi(RF)(max) maximum RF input voltage equivalent input noise voltage input resistance input capacitance 1 dB compression point of FM mixer output voltage (peak-to-peak value) Rgen = 600 ; RL = 2.8 k 70 100 mV
Vi(n)(eq) Ri Ci Ro Co Ibias Vo(max)(p-p)
- - - 100 -
2.6 1.4 5 - 5 6 -
3.1 - 7 - 7 7.2 -
nV ----------Hz k pF
Outputs: pins MIX1OUT1 and MIX1OUT2; note 5
output resistance output capacitance mixer bias current maximum output voltage (peak-to-peak value) FM mode k pF mA V
4.8 3
FM mixer
gm(conv) gm(conv)(T) conversion transconductance conversion transconductance variation with temperature noise figure 3rd-order intermodulation image rejection ratio RL = 330 ; Vi = 1 mV; note 10 8.5 - 12.5 18 mA -------V K-1
-1 x 10-3 -
F IP3 IRR IF AMPLIFIER 1 G F IP3 2003 Feb 04
- 116 25
3 119 30
4.6 - - 17.5 13 -
dB dBV dB
gain noise figure 3rd-order intermodulation
13.5 - 117
15.5 10 120
dB dB dBV
20
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
TEA6845H
SYMBOL
PARAMETER
CONDITIONS
MIN. -
TYP. -
MAX.
UNIT
Inputs: pins IFAMP1IN and IFAMP1DEC; note 10
Vi(max)(p) maximum input voltage (peak value) equivalent input noise voltage input resistance input capacitance 1 dB compression point of IF amplifier 1 output voltage (peak value) Rgen = 330 ; RL = 330 200 mV
Vi(n)(eq) Ri Ci Vo(max)(p) Ro Co IF AMPLIFIER 2 G F IP3
- 270 - 1.2 270 -
8 330 5
10 390 7 - 390 7
nV ----------Hz pF
Output: pin IFAMP1OUT
maximum output voltage (peak value) output resistance output capacitance RL = 330 ; Vi = 1 mV; note 11 1.5 330 5 V pF
gain noise figure 3rd-order intermodulation
6.5 - 127
8.5 13 130 -
10.5 15 - -
dB dB dBV
Inputs: pins IFAMP2IN and IFAMP2DEC; note 11
Vi(max)(p) maximum input voltage (peak value) equivalent input noise voltage input resistance input capacitance 1 dB compression point of IF amplifier 2 output voltage (peak value) Rgen = 330 ; RL = 330 500 mV
Vi(n)(eq) Ri Ci Vo(max)(p) Ro Co
- 270 - 1.2 270 -
10 330 5
13 390 7 - 390 7
nV ----------Hz pF
Output: pin IFAMP2OUT
maximum output voltage (peak value) output resistance output capacitance 1.5 330 5 V pF
FM demodulator and level detector; see Figs 5 and 6 FM LIMITER
Inputs: pins FMLIMIN and FMLIMDEC; note 12
G Ri Ci Vo(p-p) gain input resistance input capacitance Rgen = 50 74 270 - measured between output pins 21 500 80 330 5 - 390 7 - dB k pF
Outputs: pins QDET1 and QDET2
output voltage (peak-to-peak value) 700 mV
2003 Feb 04
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
TEA6845H
SYMBOL FM DEMODULATOR
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Limiter decoupling: pin FMLIMDEC
RL CL load resistance load capacitance AF = -3 dB 20 - - - - 10 - 50 k pF V
FM limiter inputs: pins FMLIMIN and FMLIMDEC; note 12
Vstart(lim)(rms) start of limiting of MPX output voltage (RMS value) Vo(sens)(rms) sensitivity for MPX output voltage (RMS value) 15
f = 22.5 kHz; fmod = 1 kHz; de-emphasis = 75 s (S+N)/N = 26 dB (S+N)/N = 46 dB - - 180 - - CL = 0; RL > 20 k fripple = 100 Hz to 20 kHz 200 - 10 50 15 75 V V mV A kHz dB
RDS MPX output: pin RDSMPX
Vo(rms) Io(max) Ro B PSRR RDS MPX output voltage (RMS value) maximum RDS MPX output current output resistance bandwidth RDS MPX output power supply ripple rejection f = 22.5 kHz; fmod = 57 kHz; Vi = 20 V to 1 V; note 12 230 - - 300 40 280 100 500 - -
FM MPX output: pin FMMPX; note 12
Vo(rms) MPX output voltage (RMS value) AM suppression of MPX output f = 22.5 kHz; fmod = 1 kHz; de-emphasis = 75 s; Vi = 20 V to 1 V f = 22.5 kHz; fmod = 1 kHz; m = 0.3; de-emphasis = 75 s Vi = 500 V to 300 mV Vi = 20 to 500 V Vi = 300 mV to 1 V Io(max) (S+N)/N maximum MPX output current maximum signal plus noise-to-noise ratio of MPX output voltage f = 22.5 kHz; fmod = 1 kHz; de-emphasis = 75 s; Vi = 10 mV 50 - - - 67 60 40 40 - 70 - - - 100 - dB dB dB A dB 180 230 280 mV
AM
THD
total harmonic distortion of f = 75 kHz; fmod = 1 kHz; MPX output voltage de-emphasis = 75 s; Vi = 200 V to 800 mV bandwidth MPX output power supply ripple rejection minimum load resistance 22 CL = 0; RL > 20 k fripple = 100 Hz to 20 kHz
-
0.35
0.7
%
B PSRR RL(min) 2003 Feb 04
200 - 20
- 40 -
- - -
kHz dB k
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
TEA6845H
SYMBOL Ro(max) CL(max) MPX MUTE mute tatt tdecay Idch Ich
PARAMETER maximum output resistance maximum load capacitance
CONDITIONS - -
MIN. - -
TYP.
MAX. 500 50
UNIT pF
muting depth attack time MPX mute decay time MPX mute
during RDS update CTRDSMUTE = 10 nF CTRDSMUTE = 10 nF Vo = 3 V; audio output muted Vo = 3 V; audio output not muted f = 100 kHz Ldemod = typical value Vi = 10 to 80 V Vi = 80 V to 800 mV Ldemod = 6% Vi = 10 to 80 V Vi = 80 V to 800 mV
60 0.75 0.75
80 1 1
- 1.25 1.25
dB ms ms A A
RDS update: pin TRDSMUTE
discharge current charge current 24 -24 32 -32 38 -38
DEMODULATOR AFC GAFC Voffset(DC) AFC gain 28 32 - dB
RDS MPX output: pin RDSMPX; note 12
residual DC offset voltage - - - - 0 0.2 1.4 0.1 10 0.240 25 - 0.6 1.9 40 800 50 300 - 40 1 30 1 500 V mV V mV
FM IF LEVEL DETECTOR OUTPUT: PIN Vlevel; note 12 Vlevel DC output voltage Vi = 10 V to 1 V Vi < 1 V; standard setting of level DAA Vi = 1 mV; standard setting of level DAA Vlevel Vlevel(slope) Vstep Blevel Ro RR level starting point for adjustment of step size slope of level voltage level slope adjustment of step size bandwidth of level output voltage output resistance ripple rejection VDDA1(ripple) = 100 mV (RMS); fripple = 100 Hz 7 1.1 2.5 50 950 75 - 500 - V V V mV mV -------------20 dB mV -------------20 dB kHz dB
standard setting of level slope 30 standard setting of level slope 650 Vi = 1 mV Vi = 10 mV; fmod = 22.5 kHz; standard setting of DAA 45 200 - -
2003 Feb 04
23
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
TEA6845H
SYMBOL RDS update
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Output: pin AFHOLD
Isink(max) maximum sink current after first bus transmission with AF = 1 (start of RDS update); Vo = 0.5 V no RDS update in progress; Vo = 0.5 V 1.0 1.2 1.4 mA
Output: pin AFSAMPLE
Isink(max) maximum sink current 1.0 1.2 1.4 mA
Test mode; note 3
Temperature compensation diode: pin DAATD
Vi(ext) external input voltage to clock state machine VDAATD(L) = 2.5 V; VDAATD(H) = 3.5 V VSCL(L) = 0 V; VSCL(H) = 5 V 2.5 - 3.5 V
Clock input: pin SCL
Vi(ext) external input voltage to clock DAA 0 - 5 V
Time constant output: pin T1AMAGC
Vpulse Notes 1. Measured between pins XTAL1 and XTAL2. n 2. DAA conversion gain formula: V DAAOUT = 2 x 0.75 x --------- + 0.25 x ( V DAAIN + V DAATD ) - V DAATD 128 where n = 0 to 127. 3. Reference frequency pin FREF: a) Rext = 68 k connected to ground activates the 2nd I2C-bus address b) Rext = 100 k connected to VDDA1 sets the IC into test mode. 4. Input parameters of AM mixer 1 measured between pins AMMIX1IN1 and AMMIX1IN2. 5. Output parameters of FM mixer and AM mixer 1 measured between pins MIX1OUT1 and MIX1OUT2. 6. Input parameters of AM mixer 2 measured between pins IFAMP1IN and IFAMP1DEC. 7. Output parameters of AM mixer 2 measured between pins AMMIX2OUT1 and AMMIX2OUT2. 8. Input parameters of AM IF2 measured between pins AMIF2IN and AMIF2DEC. 9. Input parameters of FM mixer measured between pins FMMIXIN1 and FMMIXIN2. 10. Input parameters of IF amplifier 1 measured between pins IFAMP1IN and IFAMP1DEC. 11. Input parameters of IF amplifier 2 measured between pins IFAMP2IN and IFAMP2DEC. 12. Input parameters of FM limiter measured between pins FMLIMIN and FMLIMDEC. enabling voltage of load PLL signal pin FREF in test mode 5.1 6 6.9 V
2003 Feb 04
24
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
TEA6845H
handbook, full pagewidth
6 Vlevel (V) 5
MHB484
4
(1)
3
(2)
2
(3)
1
0
10 -3
10 -2
10 -1
1
10
10 2
VAMIF2IN (mV)
10 3
(1) Level DAA setting byte 6 = FFH. (2) Level DAA setting byte 6 = 84H (standard setting). (3) Level DAA setting byte 6 = 00H.
Fig.3 AM level output voltage (DAA) as a function of AM level circuit input voltage.
handbook, full pagewidth
Trep
58 59 Vlevel
Vpulse
TEA6845H
61 1 k VXTAL2
test signal 16 50 4.7 nF 100 Vpulse 8.5 V 100 17 13
64 1 k 63 8.5 V oscilloscope, counter VIFAMP1IN
MHB876
Test signal: Trep = 2 ms, tr < 50 ns, tf < 50 ns, and duty factor 50%.
VIFAMP1IN = 4 V. VXTAL2 = 3 V.
Fig.4 Test circuit for AM noise blanker.
2003 Feb 04
25
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
TEA6845H
handbook, full pagewidth
6
MHB486
Vlevel (V)
5
(1)
4
3
(2)
2
(3)
1
0 10 -3
10 -2
10 -1
1
10
10 2 VFMLIMIN (mV)
10 3
(1) Level DAA setting byte 6 = FFH. (2) Level DAA setting byte 6 = 84H (standard setting). (3) Level DAA setting byte 6 = 00H.
Fig.5 FM level output voltage (DAA) as a function of FM limiter and level circuit input voltage.
2003 Feb 04
26
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
TEA6845H
handbook, full pagewidth V ,
10 FMMPX VRDSMPX (dB) 0
MHB487
(1)
9 Vlevel (V) 8 THD (%) 7
-10
-20
(2)
6
-30
5
(3)
-40
4
-50
3
-60
(4)
2
-70
(5)
1
-80 10 -3
10 -2
10 -1
1
10
10 2 VFMLIMIN (mV)
0 10 3
(1) Output voltage for FMMPX and RDSMPX: fIF = 10.7 MHz; f = 22.5 kHz; fmod = 1 kHz. (2) Noise: unweighted B = 250 Hz to 15 kHz with de-emphasis 50 s for FMMPX. (3) Noise: unweighted B = 250 Hz to 15 kHz with de-emphasis 50 s for RDSMPX. (4) THD for FMMPX and RDSMPX. (5) Level for standard setting of level DAA, byte 6 = 84H.
Fig.6 (S+N)/N, THD and level output voltage for FM mode as a function of FM demodulator input voltage.
2003 Feb 04
27
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
12 I2C-BUS PROTOCOL 12.1 I2C-bus specification
TEA6845H
order. The LSB = 0 indicates a WRITE operation to the TEA6845H. Bit 7 of each byte is considered the MSB and has to be transferred as the first bit of the byte. The data becomes valid at the output of the internal latches with the acknowledge of each byte. A STOP condition after any byte can shorten transmission times. When writing to the transceiver by using the STOP condition before completion of the whole transfer: * The remaining bytes will contain the old information * If the transfer of a byte is not completed, this byte is lost and the previous information is available. In byte 5, 4 bits are reserved for test mode purposes. Those can only be used when the test mode is activated by the select pin FREF. 12.1.3 I2C-bus pULL-UP RESISTORS
Information about the I2C-bus can be found in the brochure "The I2C-bus and how to use it" (order number 9398 393 40011). The standard I2C-bus specification is expanded by the following definitions. IC addresses: * 1st IC address C2: 1100001 * 2nd IC address C0: 1100000. Structure of the increment. I2C-bus logic: slave transceiver with auto
Subaddresses are not used. Exception to the standard I2C-bus specification: * The data hold time tHD;DAT must be at least 1 s. 12.1.1 TEST MODE
Connecting pin FREF to VDDA1 via a 100 k resistor or feeding 50 A into that pin switches the IC into the test mode. During test mode the digital-to-analog converters of the level and antenna DAA functions can be sequenced by the I2C-bus SCL line. During test mode either the TEA688x or TEF689x reference frequency, the PLL reference frequency divider or the programmable divider output can be switched to pin FREF. 12.1.2 DATA TRANSFER
When the IC is used together with the TEA688x or TEF689x and both SCL and SDA lines are connected via the I2C-bus to the TEA688x or TEF689x, the pull-up resistors of the tuner IC should be connected to the digital supply voltage of the TEA688x or TEF689x. Otherwise an I2C-bus pull-down can occur switching off the tuner IC supply when the I2C-bus buffer interface of the TEA688x or TEF689x is enabled for data transfer to the tuner IC. 12.1.4 FREQUENCY SETTING
For new frequency setting, in both AM and FM mode, the programmable divider is enabled by setting bit MUTE = 1. To select an FM frequency, two I2C-bus transmissions are necessary: * First: bit MUTE = 1 * Second: bit MUTE = 0.
Data sequence: address, byte 1, byte 2, byte 3, byte 4, byte 5, and byte 6. The data transfer has to be in this
2003 Feb 04
28
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
12.2 12.2.1 Table 1 S(1) Notes 1. S = START condition. 2. A = acknowledge. 3. P = STOP condition. Table 2 S(1) Notes 1. S = START condition. 2. A = acknowledge. Table 3 IC address byte IC ADDRESS 1 Notes 1. Defined by address pin FREF: a) 1 = 1st IC address b) 0 = 2nd IC address. 2. Read or write mode: a) 0 = write operation to TEA6845H b) 1 = read operation from TEA6845H. 12.2.2 Table 4 WRITE MODE: DATA BYTE 1 Format of data byte 1 BIT 6 PCA6 BIT 5 PCA5 BIT 4 PCA4 BIT 3 PCA3 BIT 2 PCA2 BIT 1 PCA1 1 0 0 0 0 0/1(1) Read mode address (read) A(2) I2C-bus protocol DATA TRANSFER MODE AND IC ADDRESS Write mode address (write) A(2) data byte(s) A(2)
TEA6845H
P(3)
data byte 1
MODE R/W(2)
BIT 7 AF Table 5 BIT 7 6 to 0
BIT 0 PCA0
Description of data byte 1 bits SYMBOL AF PCA[6:0] DESCRIPTION Alternative frequency. If AF = 0, then normal operation. If AF = 1, then AF (RDS) update mode. Setting of programmable counter of synthesizer PLL. Upper byte of PLL divider word.
2003 Feb 04
29
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
12.2.3 Table 6 WRITE MODE: DATA BYTE 2 Format of data byte 2 BIT 6 PCB6 BIT 5 PCB5 BIT 4 PCB4 BIT 3 PCB3 BIT 2 PCB2 BIT 1 PCB1
TEA6845H
BIT 7 PCB7 Table 7 BIT 7 to 0
BIT 0 PCB0
Description of data byte 2 bits SYMBOL PCB[7:0] DESCRIPTION Setting of programmable counter of synthesizer PLL. Lower byte of PLL divider word.
12.2.4 Table 8
WRITE MODE: DATA BYTE 3 Format of data byte 3 BIT 6 DAA6 BIT 5 DAA5 BIT 4 DAA4 BIT 3 DAA3 BIT 2 DAA2 BIT 1 DAA1 BIT 0 DAA0
BIT 7 MUTE Table 9 BIT 7 6 to 0 12.2.5
Description of data byte 3 bits SYMBOL MUTE DAA[6:0] DESCRIPTION FM audio mute. If MUTE = 0, then FM audio not muted. If MUTE = 1, then FM audio muted; writing to programmable divider enabled. Setting of antenna digital auto alignment.
WRITE MODE: DATA BYTE 4
Table 10 Format of data byte 4 BIT 7 IFMT BIT 6 RFS2 BIT 5 RFS1 BIT 4 RFS0 BIT 3 IFPR BIT 2 BND1 BIT 1 BND0 BIT 0 AMFM
Table 11 Description of data byte 4 bits BIT 7 6 to 4 3 2 and 1 0 SYMBOL IFMT RFS[2:0] IFPR BND[1:0] AMFM DESCRIPTION IF measuring time. If IFMT = 0, then IF measuring time is 20 ms. If IFMT = 1, then IF measuring time is 2 ms. Reference frequency for synthesizer. These 3 bits determine the reference frequency, see Table 12. IF counter prescaler ratio. If IFPR = 0, then IF prescaler ratio is 100. If IFPR = 1, then IF prescaler ratio is 10. Band switch. These 2 bits select in FM mode band and local or distant, see Table 13; in AM mode band and AM stereo, see Table 14. AM or FM switch. If AMFM = 0, then FM mode. If AMFM = 1, then AM mode
2003 Feb 04
30
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
Table 12 Reference frequency setting RFS2 0 1 0 1 0 1 0 1 Table 13 FM mode BND1 0 BND0 0 SELECTION RFS1 0 0 1 1 0 0 1 1 RFS0 0 0 0 0 1 1 1 1
TEA6845H
fref (kHz) 100 50 25 20 10 10 10 10
FM standard: dead zone high current charge pump active, FM AGC defined by RF level and threshold level setting by I2C-bus FM local: dead zone high current charge pump active, FM AGC source current set to maximum FM East Europe: dead zone high current charge pump switched off, current of low current charge pump set to 1 mA FM weather band: N1 divider set to 1 and I and Q phase shift network switched on, WX flag signal activated
0 1
1 0
1
1
Table 14 AM mode; note 1 BND1 0 0 1 1 Note 1. In AM mode dead zone high current charge pump switched off, current of low current charge pump set to 1 mA. BND0 0 1 0 1 SELECTION AM mono; N2 divider set to 5 (SW) AM stereo; N2 divider set to 5 (SW) AM mono; N2 divider set to 10 (LW, MW) AM stereo; N2 divider set to 10 (LW, MW)
2003 Feb 04
31
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
12.2.6 WRITE MODE: DATA BYTE 5
TEA6845H
Table 15 Format of data byte 5 BIT 7 KAGC BIT 6 WBA1 BIT 5 WBA0 BIT 4 AMSM BIT 3 TMS3 BIT 2 TMS2 BIT 1 TMS1 BIT 0 TMS0
Table 16 Description of data byte 5 bits BIT 7 6 and 5 4 3 2 1 and 0 SYMBOL KAGC WBA[1:0] AMSM TMS3 TMS2 TMS[1:0] DESCRIPTION Keyed FM AGC. If KAGC = 0, then keyed FM AGC is off. If KAGC = 1, then keyed FM AGC is on. Wide band AGC. These 2 bits set the start value of wide band AGC. For AM, see Table 17 and for FM, see Table 18. AM soft mute. If AMSM = 0, then AM soft mute is off. If AMSM = 1, then AM soft mute is on. In test mode charge pump 3-state. If TMS3 = 0, then 3-state off. If TMS3 = 1, then 3-state on. In test mode external clock for level and antenna DAA. If TMS2 = 0, then external clock disabled. If TMS2 = 1, then external clock enabled. In test mode setting of pin FREF. These 2 bits define the function of pin FREF, see Table 19.
Table 17 Setting of wide band AGC for AM WBA1 0 0 1 1 Table 18 Setting of wide band AGC for FM WBA1 1 1 0 0 WBA0 1 0 1 0 FM RF MIXER INPUT VOLTAGE (RMS VALUE) (mV) 4 8 12 16 WBA0 0 1 0 1 AM MIXER 1 INPUT VOLTAGE (PEAK VALUE) (mV) 150 275 400 525
Table 19 Setting function of pin FREF in test mode TMS1 0 0 1 1 TMS0 0 1 0 1 OUTPUT AT PIN FREF reference frequency of TEA688x or TEF689x tuner oscillator frequency divided by division ratio of programmable divider PLL synthesizer reference frequency not used (no output)
2003 Feb 04
32
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
12.2.7 WRITE MODE: DATA BYTE 6
TEA6845H
Table 20 Format of data byte 6 BIT 7 LST4 BIT 6 LST3 BIT 5 LST2 BIT 4 LST1 BIT 3 LST0 BIT 2 LSL2 BIT 1 LSL1 BIT 0 LSL0
Table 21 Description of data byte 6 bits BIT 7 to 3 2 to 0 SYMBOL LST[4:0] LSL[2:0] DESCRIPTION Setting of level DAA starting point. These 5 bits determine the offset of the level detector output voltage. Setting of level DAA slope. These 3 bits determine the steepness of the level detector output voltage.
Table 22 Standard setting of data byte 6 bits SETTING OF LEVEL DAA STARTING POINT LST4 1 12.2.8 LST3 0 READ MODE: DATA BYTE 1 LST2 0 LST1 0 LST0 0 SETTING OF LEVEL DAA SLOPE LSL2 1 LSL1 0 LSL0 0
Table 23 Format of 1st data byte BIT 7 IFC7 BIT 6 IFC6 BIT 5 IFC5 BIT 4 IFC4 BIT 3 IFC3 BIT 2 IFC2 BIT 1 IFC1 BIT 0 IFC0
Table 24 Description of data byte 1 bits BIT 7 to 0 SYMBOL IFC[7:0] DESCRIPTION IF counter result. These bits contain the last eight bits of the IF counter result.
2003 Feb 04
33
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
13 TEST AND APPLICATION INFORMATION
TEA6845H
handbook, full pagewidth
Vtune Coils: L1: P826RC-5134N=S L2: PSGAE-5078D=S L3: P293BC-1977Z L4: E543SNAS-02010 L5: 611SNS-1066Y L6: 369INS-3076X L7; 388BN-1211Z L8: air coil (1): 1 to 5 pF trimmer without DAA (2): series NP0 10 k 2.2 k 3.9 nF 100 nF 1.2 k 22 nF 100 nF 33 34 35 36 37 38 39 3.3 nF 22 3.3 H DGND fref PLL 5V digital
A B
antenna
2.2 M 3.3 H Vt BB814 L5
(1)
32 22 k BAS16 AM 10.25 MHz 120 nH 30 1 F 29 28 FM AGC F E 31 ANTENNA DAA TUNING SYSTEM D C
270 nH 8.2 pF 15 pF 290 nH BA595 22 BA595 330 2.2 k 1 nF 1 nF 15 pF L8 290 nH
1 F L6 27 8.2 pF 26 25
TEA6845H
WX
FM I/Q MIXER
x
N1
/2
G
90
RFGND 10 F 22 nF 24 90 AM-NOISE DETECTOR PEAK/ AVERAGE
H
I
J 5V analog 1 k BAQ806 100 nF 6.8 H WB FLAG 560 22 F 220 nF 23 22 21 AM RF AGC K N2 L M N
/5/10
22 nF 270 H 10 nF 1.8 M 1.5 k
20 100 pF 180 H 180 pF 100 nF 150 pF
AM MIXER 1
x
IFAMP 1 O
150 H
P 19 18 17 16 15 14 13
22 nF
22 nF
22 nF
10 nF
470 pF
1 nF
BF861C SFE10.7 MS3 10 Q
MHB878
L7 10 k
BAV99
2.2 M
22 nF
L1
47
22
22
Fig.7 Application diagram (continued in Fig.8).
2003 Feb 04
34
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
TEA6845H
handbook, full pagewidthA
4.7 k B
8.5 V 270 pF (2) AF AF SAMPLE HOLD L4 BB156 22 AM RDS/ AUDIO/IF MPX FM MPX 5V analog
3.3 H 1 H
22 nF 2.7 1.8 pF pF 40 41 42 47 F 43 44 45
6.8 nF
100 nF 47 F
100 nF
47 F
46
47
48
49
50
51
VCO C
SEQUENTIAL CIRCUIT FOR RDS UPDATING
AM DETECTOR
MUTE
POWER SUPPLY VDD (I2C-bus)
D E I2C-bus F FM IF AM IF2 IF COUNT
2 ms/ 20 ms 52 I2C-BUS 53 54 55 AM IF AGC LEVEL DAA DEMODULATOR 56
10 k
10 k SDA SCL IF2GND
G
4.7 k
L3
H BLANK PULSE AM LEVEL
57
AFC 47 F
I
58 AM/FM LEVEL
J K L M N IFAMP 2 O 63 64 12 22 nF 11 10 220 nF IF1GND 22 nF 9 8 76 5 4 22 nF 3 330 22 nF 10 F 2 1 22 nF L2 59
AM MIXER 2
x
FM LIMITER/ LEVEL
CRYSTAL OSCILLATOR
60 61 62 120 k
20.5 MHz
220 nF
P
SFE10.7 MS3 SFR450H
SFE10.7 MS3 22
Q
MHB879
8.5 V
Fig.8 Application diagram (continued from Fig.7).
2003 Feb 04
35
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
TEA6845H
handbook, full pagewidth
antenna input FM RF input fref PLL
A B C Vtune 470 k 47 3.9 nF relay 1 teledyne 33 10 k 2.2 k 100 nF 1.2 k 100 nF relay 2 34 35 36 37 22 nF 100 nF 38 39 relay 1 3.3 nF 22 100 nF D
3.3 H
DGND
32 Vt BB814 120 nH
(1)
22 k BAS16
31
ANTENNA DAA TUNING SYSTEM
E
F AM 10.25 MHz 1.5 to 5 pF 1 F 1 F BA779-2 560 pF 8.2 pF BA779-2 RFGND L7 220 nH 100 nF 47 F 22 nF L 270 BAQ806 23 22 270 WB FLAG 220 nF 1 mH 220 H 1.5 k 100 pF 330 pF 100 H 680 H 180 pF 100 nF 22 F 220 nF 21 AM RF AGC N2 M N O P 24 90 AM NOISE DETECTOR PEAK/ AVERAGE 3.3 H 22 L6 J 4:6 27 26 25 G
1 nF
8.2 pF L8 470 nH
30 29 28 FM AGC H
TEA6845H
WX
6.8 H
47 pF
FM I/Q MIXER
x
N1
/2
90
I
K
/5/10
20
AM MIXER 1
x
IFAMP 1 Q
R 1 nF 19 50 22 nF 22 nF 22 nF 18 17 16 15 14 13
470 pF
1 nF 470 k
1.2 M BF861C
4.7 F
100 nF
Ce1 Ce2
BAV99
22 nF
L1
47
22
22
10
SFE10.7 MS3 S 100 nF 304
100 nF 100 nF
330
52
2
AM RF input
IF output
IF input
MHB895
Fig.9 Test circuit (continued in Fig.10).
2003 Feb 04
36
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
TEA6845H
handbook, full pagewidth
AF SAMPLE
AF HOLD
AM RDS/ AUDIO/IF MPX
FM MPX
10 47 F 100 nF 10 47 F 100 nF 10
5V analog
A B C
(1) 4.7 k 270 pF
5V digital
L4 BB156
relay3
D
68 k
68 k
100 nF
100 nF
100 nF 47 F 10 k 10 k
8.5 V 3.3 H 100 nF
22
3.3 H
22 nF 2.7 1.8 pF pF 40 41 42 6.8 nF 47 F 43 44 45 46 47 48 49
100 nF 47 F 50 51
100 nF
SDA SEQUENTIAL CIRCUIT FOR RDS UPDATING AM DETECTOR POWER SUPPLY SCL
VCO E
MUTE
F G I2C-bus H FM IF AM IF2 IF COUNT
2 ms/ 20 ms 52 SDA I2C-BUS 53 SCL 54 IF2GND 55 DGND AM IF AGC LEVEL DAA DEMODULATOR 56 4.7 k L3 I2C-bus interface
I
J BLANK PULSE AM LEVEL
57 47 F
AFC
K
58 AM/FM LEVEL
L M N O P 120 k IFAMP 2 Q 63 64 12 11 10 9 8 7 6 5 4 3 330 22 nF 220 nF 100 nF IF1GND 100 nF 100 nF 22 F 22 nF 2 1 L2 22 220 nF 59
AM MIXER 2
x
FM LIMITER/ LEVEL
CRYSTAL OSCILLATOR
60 61 62
20.5 MHz
R
L1: P7PSG-X398 L2: P7PSGAE-5078D = S L3: 392BC-1977Z L4: E543SNAS-02010 L5: 611SNS-1066Y L6: 369INS-3076X L7: MURATA LQN L8: MURATA LQN (1): series NP0 coaxial connector test pin jumper
SFE10.7 MS3 S 100 nF 100 nF 304
SFR 450H 100 nF 2 k
SFE10.7 MS3 100 nF 100 nF 304 100 nF
to TEA6880H
330
52
2
47
330
2
52
2 k
FM IF1 output
FM IF2 AM IF2 input input
FM IF2 output
limiter input
AM IF output
MHB896
Fig.10 Test circuit (continued from Fig.9).
2003 Feb 04
37
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
Table 25 DC operating points UNLOADED DC VOLTAGE (V) SYMBOL PIN MIN. CAGC FMLIMDEC FMLIMIN AMIF2DEC IFAMP2OUT AMNBHOLD AMIF2IN IF1GND IFAMP2IN Coffset IFAMP2DEC IFAMP1OUT IFAMP1IN VDDA6 IFAMP1DEC MIX1OUT1 MIX1OUT2 VDDA5 AMMIX1IN1 AMMIX1IN2 T1AMAGC T2AMAGC IAMAGC Vref(FMMIX) FMMIXIN1 RFGND FMMIXIN2 IFMAGC T2FMAGC T1FMAGC DAAOUT DAATD DAAIN Vtune CPOUT VDDA4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 3.6 2.5 2.5 2.4 7.2 4.3 2.4 external 0 3 floating 3 7.2 2.4 external 8.5 2.4 external 8.5 external 8.5 external 8.5 2.3 2.3 0 2.5 open-collector 2.7 1 external 0 1 floating 7.5 floating - floating 0 0 0 external 8.5 - - - 8.5 8.5 8.5 0.2 0.3 8 8.3 1.3 1.6 3.1 1.3 3.4 1.6 2.75 2.75 2.8 2.8 3.1 3.1 4.6 3.1 2.7 3 4 7.9 2.7 5 - 3 4 5 4.3 3 3 2.7 7.9 4.6 2.7 AM MODE TYP. 4.8 3.5 3.5 3.2 - 5.1 3.2 MAX. 4.1 2.5 2.5 floating 3.4 8 floating external 0 2.7 3 2.7 3.6 2.3 external 8.5 2.3 external 8.5 external 8.5 external 8.5 floating floating 0 (no WX) floating open-collector 6.5 2.3 external 0 2.3 1.5 (external biasing) 3.9 1 0.2 0.2 0 0 0 external 8.5 2.8 - 4.6 - - - - - - 7.1 2.8 0.3 (no WX) 2.7 3.1 3.5 3.1 4 2.7 3.9 8.4 MIN. 4.6 2.8 2.8 FM MODE TYP.
TEA6845H
MAX. 5.1 3.1 3.1 4.4 -
3.5 4 3.5 4.4 3.1 3.1
0.5 (no WX)
7.9 3.3 3.3 4 (external biasing) 5.3 7 8.25 1.5 8.5 8.5 8.5
2003 Feb 04
38
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
TEA6845H
UNLOADED DC VOLTAGE (V) SYMBOL PIN MIN. FREF VDDD DGND VCOGND OSCFDB OSCTNK VDDA3 AFSAMPLE AFHOLD TRDSMUTE AMAFIF2 RDSMPX FMMPX VDDA2 VDDA1 SDA SCL IF2GND QDET1 QDET2 CAFC Vlevel XTAL1 XTALGND XTAL2 IREF AMMIX2OUT1 AMMIX2OUT2 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 3.2 external 5 external 0 external 0 2.2 5 external 8.5 0 open-collector 1.9 4 floating floating external 5 external 8.5 4.8 4.8 external 0 floating floating floating 0.05 1.7 external 0 1.7 4 external 8.5 external 8.5 2.1 4.25 2.5 4.5 - 2.1 7 2.5 5 5 5.2 5.2 2.2 4.3 2.5 4.6 0.2 0.5 2.8 6.1 3.4 7.2 3.4 AM MODE TYP. 3.7 MAX. 3.2 external 5 external 0 external 0 2.2 5 external 8.5 0 open-collector 0.7 (muted) floating 2.6 3 external 5 external 8.5 4.8 4.8 external 0 3.6 3.6 1.2 0 1.7 external 0 1.7 4 external 8.5 external 8.5 2.1 4.25 2.5 4.5 4.1 4.1 3.4 - 2.1 4.6 4.6 4.1 7 2.5 5 5 5.2 5.2 3.1 3.5 3.3 4 1.2 (muted) 1.7 (muted) 5.2 (not muted) 5.7 (not muted) 6.2 (not muted) 0.2 0.5 2.8 6.1 3.4 7.2 MIN. 3.4 FM MODE TYP. 3.7 MAX.
2003 Feb 04
39
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
14 PACKAGE OUTLINE QFP64: plastic quad flat package; 64 leads (lead length 1.95 mm); body 14 x 20 x 2.8 mm
TEA6845H
SOT319-2
c
y X
51 52
33 32 ZE
A
e E HE A A2 A1 (A 3) Lp bp 64 1 wM D HD ZD B vM B 19 vMA 20 detail X L
pin 1 index
wM
e
bp
0
5 scale
10 mm
DIMENSIONS (mm are the original dimensions) UNIT mm A max. 3.20 A1 0.25 0.05 A2 2.90 2.65 A3 0.25 bp 0.50 0.35 c 0.25 0.14 D (1) 20.1 19.9 E (1) 14.1 13.9 e 1 HD 24.2 23.6 HE 18.2 17.6 L 1.95 Lp 1.0 0.6 v 0.2 w 0.2 y 0.1 Z D (1) Z E (1) 1.2 0.8 1.2 0.8 7 0o
o
Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT319-2 REFERENCES IEC JEDEC MO-112 EIAJ EUROPEAN PROJECTION
ISSUE DATE 97-08-01 99-12-27
2003 Feb 04
40
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
15 SOLDERING 15.1 Introduction to soldering surface mount packages
TEA6845H
If wave soldering is used the following conditions must be observed for optimal results: * Use a double-wave soldering method comprising a turbulent wave with high upward pressure followed by a smooth laminar wave. * For packages with leads on two sides and a pitch (e): - larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be parallel to the transport direction of the printed-circuit board; - smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the transport direction of the printed-circuit board. The footprint must incorporate solder thieves at the downstream end. * For packages with leads on four sides, the footprint must be placed at a 45 angle to the transport direction of the printed-circuit board. The footprint must incorporate solder thieves downstream and at the side corners. During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. Typical dwell time is 4 seconds at 250 C. A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. 15.4 Manual soldering
This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our "Data Handbook IC26; Integrated Circuit Packages" (document order number 9398 652 90011). There is no soldering method that is ideal for all surface mount IC packages. Wave soldering can still be used for certain surface mount ICs, but it is not suitable for fine pitch SMDs. In these situations reflow soldering is recommended. 15.2 Reflow soldering
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. Several methods exist for reflowing; for example, convection or convection/infrared heating in a conveyor type oven. Throughput times (preheating, soldering and cooling) vary between 100 and 200 seconds depending on heating method. Typical reflow peak temperatures range from 215 to 250 C. The top-surface temperature of the packages should preferable be kept below 220 C for thick/large packages, and below 235 C for small/thin packages. 15.3 Wave soldering
Conventional single wave soldering is not recommended for surface mount devices (SMDs) or printed-circuit boards with a high component density, as solder bridging and non-wetting can present major problems. To overcome these problems the double-wave soldering method was specifically developed.
Fix the component by first soldering two diagonally-opposite end leads. Use a low voltage (24 V or less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 C. When using a dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds between 270 and 320 C.
2003 Feb 04
41
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
15.5 Suitability of surface mount IC packages for wave and reflow soldering methods PACKAGE(1) BGA, LBGA, LFBGA, SQFP, TFBGA, VFBGA DHVQFN, HBCC, HBGA, HLQFP, HSQFP, HSOP, HTQFP, HTSSOP, HVQFN, HVSON, SMS PLCC(4), SO, SOJ LQFP, QFP, TQFP SSOP, TSSOP, VSO Notes not suitable not suitable(3)
TEA6845H
SOLDERING METHOD WAVE REFLOW(2) suitable suitable suitable suitable suitable
suitable not not recommended(4)(5) recommended(6)
1. For more detailed information on the BGA packages refer to the "(LF)BGA Application Note" (AN01026); order a copy from your Philips Semiconductors sales office. 2. All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the maximum temperature (with respect to time) and body size of the package, there is a risk that internal or external package cracks may occur due to vaporization of the moisture in them (the so called popcorn effect). For details, refer to the Drypack information in the "Data Handbook IC26; Integrated Circuit Packages; Section: Packing Methods". 3. These packages are not suitable for wave soldering. On versions with the heatsink on the bottom side, the solder cannot penetrate between the printed-circuit board and the heatsink. On versions with the heatsink on the top side, the solder might be deposited on the heatsink surface. 4. If wave soldering is considered, then the package must be placed at a 45 angle to the solder wave direction. The package footprint must incorporate solder thieves downstream and at the side corners. 5. Wave soldering is suitable for LQFP, TQFP and QFP packages with a pitch (e) larger than 0.8 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm. 6. Wave soldering is suitable for SSOP and TSSOP packages with a pitch (e) equal to or larger than 0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm.
2003 Feb 04
42
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
16 DATA SHEET STATUS LEVEL I DATA SHEET STATUS(1) Objective data PRODUCT STATUS(2)(3) Development DEFINITION
TEA6845H
This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN).
II
Preliminary data Qualification
III
Product data
Production
Notes 1. Please consult the most recently issued data sheet before initiating or completing a design. 2. The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. 3. For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status. 17 DEFINITIONS Short-form specification The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. 18 DISCLAIMERS Life support applications These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes Philips Semiconductors reserves the right to make changes in the products including circuits, standard cells, and/or software described or contained herein in order to improve design and/or performance. When the product is in full production (status `Production'), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no licence or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified.
2003 Feb 04
43
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
19 PURCHASE OF PHILIPS I2C COMPONENTS
TEA6845H
Purchase of Philips I2C components conveys a license under the Philips' I2C patent to use the components in the I2C system provided the system conforms to the I2C specification defined by Philips. This specification can be ordered using the code 9398 393 40011.
2003 Feb 04
44
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
NOTES
TEA6845H
2003 Feb 04
45
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
NOTES
TEA6845H
2003 Feb 04
46
Philips Semiconductors
Product specification
New In Car Entertainment (NICE) car radio
NOTES
TEA6845H
2003 Feb 04
47
Philips Semiconductors - a worldwide company
Contact information For additional information please visit http://www.semiconductors.philips.com. Fax: +31 40 27 24825 For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com.
(c) Koninklijke Philips Electronics N.V. 2003
SCA75
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights.
Printed in The Netherlands
753503/02/pp48
Date of release: 2003
Feb 04
Document order number:
9397 750 10556

▲Up To Search▲

Price & Availability of TEA6845H

	To Download TEA6845H Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .